Input voltage divider calculator for AMC1300B / AMC1301 isolated amplifiers
Design Parameters
V
Peak source voltage (e.g. 240 V for mains)
mV
AMC1300B: 250 mV, AMC1301: 250 mV
mW
Power budget for the divider resistors
kΩ
AMC1300B: 22 kΩ (from datasheet)
μA
AMC1300B: 30 μA (from datasheet)
V/V
AMC1300B: 8.2 V/V
Circuit Overview
The resistive voltage divider attenuates a high-voltage source (e.g. mains) down to the
±250 mV full-scale input range of the AMC1300B/AMC1301. The divider consists of
Rtop = R1 + R2 in series, with R3 as the bottom shunt. An optional R3' on the
inverting input compensates for bias-current offset.
Assumes infinite input impedance (good for high-impedance devices like AMC1301).
Gain (VIN_FSR / Vsource)—
Rtop,min (from power budget)—
Rtop (rounded up)—
R1 = R2—
R3 — Ideal vs. Commercial (E96)
R3 (ideal)—
R3 (nearest E96)—
Error Estimates (with E96 R3)
Gain Error—
Offset Error (at input)—
Actual Vin at Vsource,max—
Output at Vsource = 0 V (offset only)
Vin at 0 V (bias offset)—
Vout at 0 V (after AMC gain)—
Design II — Compensated Divider (with R3')
Accounts for finite input impedance (Rind) and bias-current offset. Recommended for AMC1300B.
Ideal Values
R3 (ideal, compensated)—
R3' (ideal)—
Nearest Commercial Resistors (E96, 1%)
R3 (nearest E96)—
R3' (nearest E96)—
Error with Commercial Resistors
Gain Error (with E96 R3)—
Offset Error (at input, with E96 R3 & R3')—
Offset Error (at output)—
Formulas Used
R3 = (Gain × Rtop) / (1 − Gain − Gain × 2Rtop / Rind)
R3' = (Rtop × R3) / (Rtop + R3)
Gain Err = R3 / Rind × 100%
Offset Err = Ibias × (R3 − R3') at input
Input RC Filter
A capacitor C across R3 forms a low-pass filter to reject high-frequency noise.
The cutoff frequency is fc = 1 / (2π × R3 × C).
Enter your desired cutoff frequency to get the recommended C value.
V_inP
|
[R3]──┬── to AMC input
| |
| [C] ← filter cap across R3
| |
GND GND
Hz
Typical: 50–10k Hz depending on application
Design I — C for R3
C (ideal) using E96 R3—
C (nearest E96 cap)—
Actual fc with E96 values—
Design II — C for R3
C (ideal) using E96 R3—
C (nearest E96 cap)—
Actual fc with E96 values—
Output Summary
Vout,diff at Vsource,max—
Vout,CM—
Custom Design — Enter Your Own Resistors
Enter your actual resistor values to see the resulting voltage, gain error, and offset error.
V
Ω
Ω
Ω
Ω
Ω
μA
V/V
V
AMC1300B: 1.44 V, AMC1301: 1.44 V
Custom Design Results
Divider Output
Rtop (R1 + R2)—
Divider ratio (ideal)—
Vin at Vsource,max (ideal)—
Vin at Vsource,max (with Rind)—
Errors
Gain Error (R3 / Rind)—
Offset Error (at input)—
Offset Error (at output)—
Input at Vsource = 0 V
Vin at 0 V (bias offset)—
AMC Output at Vsource,max
VoutP (+)—
VoutN (−)—
Vout,diff = V(+) − V(−)—
Vout,CM—
AMC Output at Vsource = 0 V
VoutP (+) at 0 V—
VoutN (−) at 0 V—
Vout,diff at 0 V—
Power
Power in divider—
Reference
Based on TI Application Note SBAA350A —
Isolated Voltage-Measurement Circuit With ±250-mV Input and Differential Output
(Daniel Miller, Alex Smith, June 2020, Rev. September 2021).
E96 resistor series (1% tolerance) used for commercial value selection.